Lesson Plans: Introduction Lesson Plan 1: Be Direct - Oil Spills on Land Lesson Plan 2: Very Varied - Inverse Variation

Lesson Plan 2: Very Varied - Inverse Variation

Supplies:

Teachers will need the following:
• cylindrical jars (about eight to 12) of various sizes, each jar identified by a number for easy reference
Students will need the following:
• notebook or journal
• pens/pencils
For each group of four students, you will need:
• overhead transparency sheet (preferably with gridlines)
• ruler
• water (at least 200 ml)

Steps

Introductory Activity:

1. Give students the two sets of data below to review. Have them determine, using whatever method they choose, whether each of the data sets is a direct variation.

A.
 x y 2 5 4 10 7 17.5 10 25

B.
 x y -2 4 -1 1 0 0 3 9
• Which of these represents a direct variation?
(Answer: Only set A, because it has a constant rate of change. Although set B passes through the origin, it does not have a constant rate of change.)
• Does the data in set A pass through the origin?
• What is the constant of proportionality for set A?
(Answer: The slope of the line given by , or 2.5.)

Learning Activities:

1. Have one student read aloud from the bottom of page 168 in the SIMMS handout.

As soon as a quantity of oil is spilled, it starts to spread. If not contained, the resulting slick can cover a very large area. As the oil continues to spread, the depth of the slick decreases. In the following exploration, you investigate the relationship between the depth of a spill and the area it covers.

2. Explain to students that they will be conducting an exploration similar to the one for direct variation. A set amount of water (200 ml) will be placed into cylinders of various sizes. Each group must collect data for all of the cylinders the teacher provides.

3. All students should create a chart in their notebooks, as follows:

 Jar Number Diameter (cm) Area of Base (cm²) Height of Water (cm) Volume of Water (cm³)

4. Inform students that they will measure the diameter of each jar to the nearest tenth of a centimeter and will use that measurement to calculate the area of the base of the jar. Be sure, however, to emphasize that students must measure the inside diameter of the jar, not the outside diameter. That is, they need to ignore the thickness of the jar.

5. Students should calculate the volume of the water in cubic centimeters, based on the area of the jar's base and the depth of the water.

6. Explain that each group will be required to create a scatterplot that gives the area of the base (in cm²) along the x-intercept and the depth of the water (in cm) along the y-axis. Distribute a transparency sheet and an overhead pen to each group, and tell them that they may be asked to explain their scatterplot to the class.

7. Using each of the jars, have students complete their charts and create scatterplots.

8. As students work, circulate among the groups. Offer assistance as necessary, but do not provide too much information.

9. Once the groups have completed their scatterplots, call on two or three to present them to the class. The students should answer these questions:
• Pick a point (x, y). What is its meaning in the context of this problem?
• Is the relationship between area and depth linear?
• Based on the data you collected, what happens when the area of the base increases? What happens when the area of the base decreases?
10. Involve the rest of the class by asking the following questions.
• Does the relationship in your graph appear to be a direct variation? (Answer: No.)
• What should the number in last column be, approximately?
• Why?
• But this column for volume is measured in cm³, not ml. Why does it still work?
(Answer: Because in the metric system, 1 ml = 1 cm³.)
• Why are the numbers not exactly 200, but only close to it?
(Answer: It's difficult to measure the depth of the water, the diameter of the cylinder, etc., so there may be a slight margin of error.)
11. Allow groups a few minutes to generate an equation that describes the graph. Encourage students to think about how the graph was generated: the volume of the water is equal to the base of the jar times the depth of the water; that is, V = Bh, or
200 = xy. To graph this function, it should be rewritten in the form y = 200/x.

12. Point out that this is not a direct variation; it's not linear, and it does not pass through the origin. Ask students what they think this relationship might be called instead. Explain to them that it is known as an "indirect proportion," or "inverse variation."

13. Review by comparing and contrasting direct and inverse variations:
• The graph of a direct variation contains the origin (0, 0) and is linear; that is, it has a constant rate of change. It can be written in the form y = mx, where m is the slope or the constant of proportionality.

• The graph of an indirect variation is a curve with no x-intercept or y-intercept; that is, it never crosses the axes. It does not contain the origin, and it can be written in the form , where k is the constant of proportionality.

• Point out that is constant in a direct proportion; direct proportion implies that the quotient of variables is constant.

• On the other hand, xy is constant in an indirect proportion; indirect proportion implies that the product of variables is constant.
14. Ask the class for examples of direct and indirect variations. For each example, have students attempt to explain the corresponding graph. For indirect variation, students may have difficulty generating an example, so it may be necessary to have an example of your own prepared.

Culminating Activity/Assessment:

Assign several exercises for independent practice and homework. You may assign any of the problems from 3.1 through 3.9 (pages 170-174) in the SIMMS textbook.